welded sonic testing tube

Ultrasonic Testing for Pipe and Tube | Penn Stainless Products

Ultrasonic Testing for Pipe and Tube. Ultrasonic Testing (UT) utilizes sound energy at high frequencies to provide examinations and measurements of the stainless steel product. This aids in flaw detection/evaluation, dimensional measurements, etc.

Easy-to-install sonic tube system for CSL - Dextra Group

Sonitec is a tube solution invented to facilitate the integrity testing of foundations using the CSL testing method. CSL (Cross Sonic Logging) method allows to determine the structural integrity and homogeneity of concrete within diaphragm walls, bored piles, drilled …

Radiographic and Ultrasonic Testing of Welds - ESAB

Radiographic Testing (RT) – This method of weld testing makes use of X-rays, produced by an X-ray tube, or gamma rays, produced by a radioactive isotope. The basic principle of radiographic inspection of welds is the same as that for medical radiography.

Sonic Tube, Sonic Tube Suppliers and Manufacturers at ...

sonic tube is the Push-Fit SYSTEM available on the market dedicated for sonic test applications. ,Ltd is the subsidiary company of Shandong Hongsheng Steel Pipe Co., Ltd . is the largest manufacturing and sales enterprise for galvanized steel pipe ,seamless steel pipe and fittings in …

Ultrasonic welding - Wikipedia

Ultrasonic welding is an industrial technique whereby high-frequency ultrasonic acoustic vibrations are locally applied to workpieces being held together under pressure to create a solid-state weld. It is commonly used for plastics , and especially for joining dissimilar materials .History·

Welded Sonic Tube, Welded Sonic Tube Suppliers and ...

Alibaba offers 94 welded sonic tube products. About 12% of these are steel pipes, 1% are plastic tubes. A wide variety of welded sonic tube options are available to you, such as q195, 10#, and 20#.[PDF]

A GUIDE FOR ULTRASONIC TESTING AND EVALUATION …

from 1 to 5 MHz on the cathode ray tube. The instrument shall ... PracticeJ American Society for Nondestructive Testing, shall apply. Ultrasonic testing may be carried out by a Level 11 operator or by a Level I operator under the direct supervision of a Level 11 operator.

Sonic Tube, Sonic Tube Suppliers and Manufacturers at ...

sonic tube is the Push-Fit SYSTEM available on the market dedicated for sonic test applications. ,Ltd is the subsidiary company of Shandong Hongsheng Steel Pipe Co., Ltd . is the largest manufacturing and sales enterprise for galvanized steel pipe ,seamless steel pipe and fittings in …

Ultrasonic welding - Wikipedia

Ultrasonic welding is an industrial technique whereby high-frequency ultrasonic acoustic vibrations are locally applied to workpieces being held together under pressure to create a solid-state weld. It is commonly used for plastics , and especially for joining dissimilar materials .History·

Welded Sonic Tube, Welded Sonic Tube Suppliers and ...

Alibaba offers 94 welded sonic tube products. About 12% of these are steel pipes, 1% are plastic tubes. A wide variety of welded sonic tube options are available to you, such as q195, 10#, and 20#.[PDF]

A GUIDE FOR ULTRASONIC TESTING AND EVALUATION …

from 1 to 5 MHz on the cathode ray tube. The instrument shall ... PracticeJ American Society for Nondestructive Testing, shall apply. Ultrasonic testing may be carried out by a Level 11 operator or by a Level I operator under the direct supervision of a Level 11 operator.

ASTM E273 - 15 Standard Practice for Ultrasonic Testing of ...

1.1 This practice 2 describes general ultrasonic testing procedures for the detection of discontinuities in the weld and adjacent heat affected zones of welded pipe and tubing by scanning with relative motion between the search unit and pipe or tube.

GE's GRP Ultrasonic Tube & Pipe Tester | GE Digital Solutions

GRP is a full body ultrasonic tube and pipe tester with stationary probes system or portal solutions with moving probes for seamless and Electrical Resistance Welded (ERW) tubes. Models for different test techniques are available in diameters from 60 to 500 mm.

Radiographic and ultrasonic weld inspection - The Fabricator

thefabricator› Article› Testing and MeasuringRadiographic and ultrasonic weld inspection are the two most common nondestructive testing (NDT) methods used to detect discontinuities within the internal structure of welds. The obvious advantage of both of these testing methods is their ability to help establish the weld's internal integrity without destroying the welded component.[PDF]

Ultrasonic testing of welded joints in pipelines. New ...

sonic testing of welded butt joints with diameters of up to 500 mm and wall thicknesses of 2 to 10 mm. Such pipelines are commonly used for feeding oil and petrol products, in gas-supply networks in pop-

Heat Exchanger Services - National Heat Exchange

Besides heat exchanger cleanings our services also include vacuum testing, tube plugging, retubing, turbine lube oil flushing, condenser cleaning, and more.

Manual Ultrasonic Testing - NDT inspection | TWI

Manual ultrasonic testing is one of the more common non-destructive testing methods performed on materials. This testing utilises high frequency mechanical energy, i.e. sound waves, to conduct examinations and measurements on a test area. Typically the UT inspection system consists of a transducer, pulser/receiver, and display unit.[PDF]

Heat Exchanger Tubes - Vallourec

as-welded tube passes through a final, multi-stage sizing mill. ... sonic, Eddy Current, pneumatic and hydraulic testings. Leaders in ultrasonic testing Vallourec Heat Exchanger Tubes was the first company in the world to develop ultrasonic testing on welded tubes, as early as in[PDF]

A GUIDE FOR THE NONDESTRUCTIVE TESTING OF …

SSC-253.-. A GUIDE FOR THE NONDESTRUCTIVE TESTING OF NON-BUTT WELDS IN COMMERCIAL SHIPS PART ONE This document has been approved for public release and sale; its distribution is unlimited.[PDF]

Manual ultrasonic inspection of thin metal welds

17640:2010. This standard is specified to be applied for the testing of fusion welded joints in metallic material of thickness greater than or equal to 8mm and where both the welded parent material are ferritic. The probe frequency specified in this standard are to be within the range 2 and 5MHz.[PDF]

LASER WELDING OF CO-EXTRUDED TUBING - Clearweld

LASER WELDING OF CO-EXTRUDED TUBING . William H. Cawley, GENTEX Corporation, Carbondale, PA 18407-0315, USA ... Would the tubing and welded products pass Class VI testing? How would gamma and ethylene oxide sterilization affect the product? Would ... luer-tube connection rather than rotating the connection.

Hot Products

We are here to serve you!

Reply to technical consultation Provide design solution Dispatch engineers domestically/abroad Handle complaints thoroughly Systematic training Trouble judgment &amo; removal