cold work tool steel d2

HTCourses Cold work Tool steel D2 - HTCourses

D2 Tool Steel. The popular tool steel which is considered to be a High Carbon High Chromium Cold Work tool steel is known by the international designation of D2 and is a very popular tool steel that can be used for many applications.

D2 Tool Steel | 1.2379 | X153CrMo12 | Cr12MoV | SKD11

SAE D2 tool steel is a high carbon (1.4-1.6% C), high chromium Cold tool steel (11-13% chrome), and with Very high wear resisting properties, heat treatment can be reached to 60-62 HRc. D2 steel have very wear resistant property but not as tough as lower alloy steel.

AISI D2 | AISI D2 Tool Steel | AISI D2 Cold Work Tool Steel

AISI D2 steel is Cold Work Steel with High Carbon High Chromium contents. The Quality with high wear resistant and toughness properties due to Vanadium addition of 0.90% . Normally it supply condition is an Annealed and will offer hardness to reach 57-59 HRC.

Cold Work Tool Steel | Saaj Steels Corporation | Cold Work ...

Cold Work Tool Steel D2. D2 steel is an air hardening, high-carbon, high-chromium tool steel. It has high wear and abrasion resistant properties. It is heat treatable and will offer a hardness in the range 55-62 HRC, and is machinable in the annealed condition. D2 steel shows little distortion on correct hardening.

Cold Work Tool Steel Supplier- D2 | D3 | A2 | O1

Cold Work Steel Description These steels are aimed at the manufacturing of tools used in cold processing of other steels, cast irons and non ferrous metals and in diversified operations such as cutting, bending, forming, coining, extrusion, steel wire drawings, wooden work, ceramic pressing, pigment grinding, rock drilling, paper cutting and ...

D2 Tool Steel - Special steel china supplier-OTAI Special ...

AISI D2 is a cold work tool steel.Cold work die steel D2 steel with high abrasion resistance, micro deformation, the wind hard tool steel, carbon content as high as 1.5%, chromium content as high as 11.5%, the heat treatment hardness can reach 60 HRC.

Cold Work Tool Steel - Special steel china supplier-OTAI ...

A2 Tool Steel. AISI A2 Steel is a high quality Cold work tool steel, It belong to the high quality high carbon alloy tool steel. typical applications include cold forging dies, coining dies, cold heading dies, shear blades, knurling tools and as cutting knives for paper, wood, fibre and resin-bonded aterial, etc.

ASTM A681, for Tool Steels Alloy - Otai Special Steel

Material in accordance with ASTM A681 specification is classified by chemical composition. There are Hot Work Tool Steel, Cold Work Tool Steel, Shock-Resisting Steels, Special-Purpose Tool Steels, Plastic Mold Tool Steel. Common steel grades: H11, H13, A2, D2, D3, O1, P20 etc.

Blade Materials - Carolina Knife Co.

D2-High Carbon Cold Work Tool Steel An air-hardened tool steel, AISI D2 contains high carbon and chromium levels. In fact D2 contains almost enough chromium to be considered stainless steel, and is often referred to as semi-stainless.[PDF]

COLD WORK TOOL STEEL AISI D2 - S&T Stainless

COLD WORK TOOL STEEL – AISI D2 AISI D2 Cold Work Tool Steel air or oil hardening, with maximum dimensional stability during heat treatment, offering very high hardness and abrasion resistance. Generally supplied annealed to HB 250 max. TYPICAL APPLICATIONS: Deep drawing and forming dies, cold drawing punches, hobbing, blanking, lamination and

Tool steel - Wikipedia

It is a cold work oil-hardening, graphitic tool steel with outstanding resistance to metal-to-metal sliding wear and galling. APPLICATIONS: Thread gauges, master gages, cams, bushings, sleeves, ... D2 is very wear resistant but not as tough as lower alloyed steels. The mechanical properties of D2 are very sensitive to heat treatment.Water-hardening group·

D2 Tool Steel | 1.2379 | SKD11 Tool Steel - Otai Special Steel

Cold Works D2 tool steel is a high carbon, high chromium tool steel (12% chrome) with extremely high wear resisting properties, heat treatable to 60-62 Rc. D2 steel is very wear resistant but not as tough as lower alloyed steels.

Cold Work Tool Steel Bar Manufacturers and Suppliers in ...

Cold Work Tool Steel D2. D2 steel is an air hardening, high-carbon, high-chromium tool steel. It has high wear and abrasion resistant properties. It is heat treatable and will offer a hardness in the range 55-62 HRC, and is machinable in the annealed condition. D2 steel shows little distortion on correct hardening.

S7, D2, A2: Difference in tool steel properties | Paulo

S7 tool steel is a versatile formulation suitable for both cold and hot work service. It has a relatively low carbon concentration compared to D2 and A2 steels (0.45 – …

D2, 1.2379 Cold Work Tool Steel, Alloy Tool Steel

Very high resistance against abrasive and adhesive wear due to a high volume of hard carbides in the steel matrix, moderate machinability,good dimensional stability, toughness and through hardenability.[PDF]

AISI D2 | Cold Work Tool Steel | Data Sheet

AISI D2 7 Further information Contact your local Uddeholm office for further information on the selection, heat treatment, appli-cation and availability of Uddeholm tool steels, including the publications “Steels for Cold Work Tooling”. Electrical-discharge machining

Tool Steel D2 | All Metals & Forge Group

Tool Steel D2 Principal Design Features. This alloy is one of the Cold Work, high carbon, high chromium type tool steels. D2 is a deep hardening, highly wear resistant alloy. It hardens upon air cooling so as to have minimum distortion after heat treatment. Applications.

D2 Tool Steel - High-Carbon, High-Chromium, Cold-Work ...

Cold-work tool steels include the high-carbon, high-chromium steels or group D steels. These steels are designated as group D steels and consist of D2, D3, D4, D5, and D7 steels. These steels contain 1.5 to 2.35% of carbon and 12% of chromium. Except type D3 steel, all the other group D steels include 1% Mo and are air hardened.

Cold Work Tool Steel - ssm.co.nz

Cold work steel is exposed to high stresses and requires great resistance against wear, impact and bending. The development of new steel grades is mainly guided by analyzing damage suffered by tools in various processes. In each area of use, properties are sought which will extend the working life of the tool. Different types of wear demand ...

SAE-AISI D2 (T30402) Chromium Cold-Work Steel ...

SAE-AISI D2 steel is a tool steel. D2 is the designation in both the SAE and AISI systems for this material. T30402 is the UNS number. It can have the highest ductility among the tool …

Hudson Tool Steel allows users to compare the qualities ...

M2 high-speed steel and H13 hot work steel are included in the property comparisons because both are sometimes used in cold work tooling applications and to provide a common reference for comparisons with the properties of the high-speed and hot work tool steels.

Cold Work Tool Steel - Tool Steel-High Speed Steel China ...

ASTM A681, JIS G 4404, DIN 17350, GB/T 1299, SS14. AISI-SAE D2 steel is a Chrome-Vanadium Cold Work Tool Steel. Cr chemical composition-11.0~13.0%. After the …

D2 Tool Steel - univstainless

D2 is an AOD melted cold work, high carbon, high chromium tool steel with excellent hardenability. It has excellent wear resistance better than both A and O series tool steels. This material hardens with an air cool allowing minimal dimensional issues after heat treatment.

Tool Steel Products - Tool Steels - Tool Steel Service Inc.

Tool Steel Products - Tool Steels Tool Steel Service is a leading supplier of Tool Steel Products distributing products throughout North America. Tool Steel Service maintains an extensive inventory of tool steel with stock in tool steel rounds, tool steel flats and precision ground products.[PDF]

TOOL STEEL - Since 1948

D2 is an air-hardening, high carbon, high chromium tool steel with extremely high wear resisting properties. It is a very deep hardening steel and will be practically free from size change after proper treatment. The high percentage of chromium gives it mild corrosion-resisting properties in the hardened condition. TYPICAL APPLICATIONS

D2 Tool Steel - West Yorkshire Steel - Special Steel

D2 tool steel stockholders and suppliers, delivering to the whole of the UK. West Yorkshire Steel are suppliers of D2 tool steel in round bar, plate, sheet and block which can be bandsaw cut to your requirements. A high carbon high chromium tool steel grade offering very …

Die & Tool Steel - D3 Round Die Steel. Manufacturer from ...

Die & Tool Steel We are leading importer exporter and supplier from Mumbai, our product range includes Die & Tool Steel such as Cold Work Steel, O1 Tool Steel, D2 Die Steel and D3 Tool Steel.

Cold Work Tool Steel - D2 Tool Steel Manufacturer from …

Cold Work Tool Steel Our range of products include d2 tool steel, die steel, plastic mold steel, cold work tool steel and carbon alloy steel.

Hot Products

We are here to serve you!

Reply to technical consultation Provide design solution Dispatch engineers domestically/abroad Handle complaints thoroughly Systematic training Trouble judgment &amo; removal